Volume 31, Issue 4 (12-2023)
www.ijcm.ir 2023, 31(4): 785-794 |
Back to browse issues page
Download citation:
BibTeX | RIS | EndNote | Medlars | ProCite | Reference Manager | RefWorks
Send citation to:
BibTeX | RIS | EndNote | Medlars | ProCite | Reference Manager | RefWorks
Send citation to:
Ataei M, Fadavieslam M R F. The effect of substrate temperature on the preparation of molybdenum oxide thin films by spray pyrolysis method used in diode. www.ijcm.ir 2023; 31 (4) :785-794
URL: http://ijcm.ir/article-1-1798-en.html
URL: http://ijcm.ir/article-1-1798-en.html
1- School of Physics, Damghan University, Damghan, Iran.
Abstract: (744 Views)
In this research, the diodes were made using a thin films of molybdenum oxide on the doped P-type silicon substrate with the aim of studying the effect of the substrate temperature on the characteristics of the diode. For this purpose, thin films of molybdenum oxide were deposited on the substrate at substrate temperatures of 350, 400, 450 and 500 ˚C by spray pyrolysis. The structural and optical properties of the thin films were characterized. They show a fairly crystalline nature with a straight structure and peaks corresponding to (020), (040) and (060) planes, with the preferred peak being (040) in all samples. The shape of the surface of the samples is without cracks and has a rectangular granulation with the size of the grains in the range of 110 to 210 nm. Also, their average surface roughness was measured in the range of 157 to 167 nm. The optical gap of the samples was estimated in the range of 2.84 to 2.95 eV. The voltage-current diagram of the samples showed their diode behavior. The diode made at 400 ˚C substrate temperature has the lowest threshold voltage.
References
1. [1] Acosta Edwin, "Thin Films/Properties and Applications." In Thin Films. Intech Open, 2021. [DOI:10.5772/intechopen.95527]
2. [2] Yuonesi M., Izadifard M., Ghazi M. E., GHODSI F. ESMAILI, "Influence of Co and Fe substitution on optical and structural properties of zinc oxide thin films." Iranian Journal of Crystallography and Mineralogy 19 (2011): 65-72.
3. [3] Kumar Anil, Chandra Shekhar Prajapati, Sahay P. P., "Results on the microstructural, optical and electrochromic properties of spray-deposited MoO3 thin films by the influence of W doping." Materials Science in Semiconductor Processing 104 (2019): 104668. [DOI:10.1016/j.mssp.2019.104668]
4. [4] Ghaleghafi E, Rahmani M., ''Fabrication, characterization and investigation of gas sensing properties of MoO3 thin films. Iranian Journal of Crystallography and Mineralogy. 2019;27(2):475-86 [DOI:10.29252/ijcm.27.2.475]
5. [5] Yusuf Bashir, Mohd Mahadi Halim, Md Roslan Hashim, Mohd Zamir Pakhuruddin, "Structural, optical, and electrical properties of spray-pyrolyzed MoO3 thin films by varying precursor molarity, as hole-selective contact for silicon-based heterojunction devices." Journal of Materials Science: Materials in Electronics 31, no. 23 (2020): 21802-21812. [DOI:10.1007/s10854-020-04692-x]
6. [6] Mousavi-Zadeh Seyyed Hamid, Mohammad Bagher Rahmani, "Synthesis and ethanol sensing characteristics of nanostructured MoO3: Zn thin films." Surface Review and Letters 25, no. 01 (2018): 1850046. [DOI:10.1142/S0218625X18500464]
7. [7] Sayede A. D., Amriou T., Pernisek M., Khelifa B., Mathieu C., "An ab initio LAPW study of the α and β phases of bulk molybdenum trioxide, MoO3." Chemical physics 316, no. 1-3 (2005): 72-82. [DOI:10.1016/j.chemphys.2005.04.036]
8. [8] Kamoun O., Boukhachem A., Amlouk M., Ammar S., "Physical study of Eu doped MoO3 thin films." Journal of Alloys and Compounds 687 (2016): 595-603. [DOI:10.1016/j.jallcom.2016.06.022]
9. [9] Bouzidi A., Benramdane N., Tabet-Derraz H., Mathieu C., Khelifa B., Rachel Desfeux, "Effect of substrate temperature on the structural and optical properties of MoO3 thin films prepared by spray pyrolysis technique." Materials Science and Engineering: B 97, no. 1 (2003): 5-8. [DOI:10.1016/S0921-5107(02)00385-9]
10. [10] Abinaya A., Jeyaprakash B. G., "Structural, surface and mechanical characterization of spray-deposited molybdenum disulfide thin films." Materials Science in Semiconductor Processing 31 (2015): 582-587. [DOI:10.1016/j.mssp.2014.12.045]
11. [11] Patil P. R., Patil P. S., "Preparation of mixed oxide MoO3-WO3 thin films by spray pyrolysis technique and their characterisation." Thin Solid Films 382, no. 1-2 (2001): 13-22. [DOI:10.1016/S0040-6090(00)01410-3]
12. [12] Khalate S. A., Kate R. S., Pathan H. M., Deokate R. J., "Structural and electrochemical properties of spray deposited molybdenum trioxide (α-MoO3) thin films." Journal of Solid-State Electrochemistry 21, no. 9 (2017): 2737-2746. [DOI:10.1007/s10008-017-3540-4]
13. [13] Balaji M., Chandrasekaran J., Raja M., Rajesh S., "Structural, optical and electrical properties of Ru doped MoO3 thin films and its P-N diode application by JNS pyrolysis technique." Journal of Materials Science: Materials in Electronics 27, no. 11 (2016): 11646-11658. [DOI:10.1007/s10854-016-5300-0]
14. [14] Kamoun O., Boukhachem A., Alleg S., Jeyadevan B., Amlouk M., "Physical study of nano-structured MoO3 films codoped with cobalt and nickel in which there is a ferro-diamagnetic transition." Journal of Alloys and Compounds 741 (2018): 847-854. [DOI:10.1016/j.jallcom.2018.01.231]
15. [15] Fadavieslam, ''Deposition and characterization of SnO2:Sb thin films fabricated by the spray pyrolysis method''. Iranian Journal of Crystallography and Mineralogy. 2019;27(3):739-46. [DOI:10.29252/ijcm.27.3.739]
16. [16] Pakniyat, Motevalizadeh, Jami, ''The effect of Ga-doping on the structural and optical properties of ZnO thin films prepared by spray pyrolysis''. Iranian Journal of Crystallography and Mineralogy. 2019;27(3):747-52. [DOI:10.29252/ijcm.27.3.747]
17. [17] Faraji S., Bagheri-Mohagheghi M-M., Mousavi M., "Study of the Synthesis Process of MoO3 to MoS2 Thin Films Deposited by Spray Pyrolysis: The Effect of [S/Mo] Mole Concentration and Sulfurization Process." Journal of Electronic Materials 50, no. 6 (2021): 3341-3347. [DOI:10.1007/s11664-021-08826-7]
18. [18] Martínez H. M., Torres J., López-Carreño L. D., Rodríguez-García M. E., "The Effect of substrate Temperature on the Optical Properties of MoO3 Nano-crystals prepared using spray pyrolysis." Journal of Superconductivity and Novel Magnetism 26, no. 7 (2013): 2485-2488. [DOI:10.1007/s10948-012-1692-0]
19. [19] Ghazkoob Z., Zargar M., Kazeminejad I. Lari, S.M., ''Synthesis of BiVO4 nanoparticles by the co-precipitation method and study the crystal structure, optical and photocatalytic properties of them''. Iranian Journal of Crystallography and Mineralogy. 2020;28(3):797-806. [DOI:10.29252/ijcm.28.3.797]
20. [20] Benameur N., Chakhoum M. A., Boukhachem A., Dahamni M. A., Ghamnia M., Hacini N., Pireaux J-P., Houssiau J-P., Ziouche A., "Investigation of some physical properties of pure and Co-doped MoO3 synthesized on glass substrates by the spray pyrolysis method." Journal of Electron Spectroscopy and Related Phenomena 234 (2019): 71-79. [DOI:10.1016/j.elspec.2019.05.015]
21. [21] Deokate, Ramesh J., Ranjit Kate, Nanasaheb M. Shinde, Rajaram S. Mane, "Energy storage potential of sprayed α-MoO 3 thin films." New Journal of Chemistry 45, no. 2 (2021): 582-589. [DOI:10.1039/D0NJ03910A]
22. [22] Vivek P., Chandrasekaran J., Marnadu R., Maruthamuthu S., ''Fabrication of Illumination-dependent Cu/p-Si schottky barrier diodes by sandwiching MoO3 nanoplates as an interfacial layer via JNSP technique''. Journal of Electronic Materials, 49 (2020) 4249-4264. [DOI:10.1007/s11664-020-08137-3]
23. [23] Srinivasan, Parthasarathy, John Bosco Balaguru Rayappan, "Growth of α-MoO3 golf ball architectures with interlocking loops for selective probing of trimethylamine at room temperature." Materials Research Bulletin 130 (2020): 110944. [DOI:10.1016/j.materresbull.2020.110944]
24. [24] Chaturvedi, Neha, Sanjay Kumar Swami, Viresh Dutta, "Electric field assisted spray deposited MoO3 thin films as a hole transport layer for organic solar cells." Solar Energy 137 (2016): 379-384. [DOI:10.1016/j.solener.2016.08.038]
25. [25] Afify H. H., Hassan S. A., Abouelsayed A., Demian S. E., Zayed H. A., "Coloration of molybdenum oxide thin films synthesized by spray pyrolysis technique." Thin Solid Films 623 (2017): 40-47. [DOI:10.1016/j.tsf.2016.12.033]
26. [26] Mahajan S. S., Mujawar S. H., Shinde P. S., Inamdar A. I., Patil P. S., "Structural, morphological, optical and electrochromic properties of Ti-doped MoO3 thin films." Solar energy materials and solar cells 93, no. 2 (2009): 183-187. [DOI:10.1016/j.solmat.2008.09.025]
27. [27] Boukhachem A., Kamoun O., Mrabet C., Mannai C., Zouaghi N., Yumak A. Y. Ş. E., Boubaker K., Amlouk M., "Structural, optical, vibrational and photoluminescence studies of Sn-doped MoO3 sprayed thin films." Materials Research Bulletin 72 (2015): 252-263. [DOI:10.1016/j.materresbull.2015.08.011]
28. [28] Asadpour Arzefooni, Izadifard, Ghazi, ''Investigation of structural and optical properties of CH3NH3SnI3 Perovskite layers synthesized by one-step thermal evaporation technique''. Iranian Journal of Crystallography and Mineralogy. 2020;28(4):1037-50. [DOI:10.52547/ijcm.28.4.1037]
29. [29] Asadpour Arzefooni, Izadifard, Ghazi, Arab Pour, ''Study of Structural, Optical and Electrical Properties of MA(FA)SnICl2 Perovskite Thin Films Synthesized by One-Step Spin Coating'', Iranian Journal of Crystallography and Mineralogy, 29 (2021) 919-932. [DOI:10.52547/ijcm.29.4.919]
30. [30] Boudaoud, L., N. Benramdane, A. Bouzidi, A. Nekerala, Rachel Desfeux. "(MoO3) 1− x (V2O5)x thin films: Elaboration and characterization." Optik 127, no. 2 (2016): 852-854. [DOI:10.1016/j.ijleo.2015.10.105]
31. [31] Chandoul F., A. Boukhachem F. Hosni, Moussa H., Fayache M. S., Amlouk M., Raphaël Schneider, "Change of the properties of nanostructured MoO3 thin films using gamma-ray irradiation." Ceramics International 44, no. 11 (2018): 12483-12490. [DOI:10.1016/j.ceramint.2018.04.040]
32. [32] Vivek P., Chandrasekaran J., Marnadu R., Maruthamuthu S., Balasubramani V., Balraju P., "Zirconia modified nanostructured MoO3 thin films deposited by spray pyrolysis technique for Cu/MoO3-ZrO2/p-Si structured Schottky barrier diode application." Optik 199 (2019): 163351. [DOI:10.1016/j.ijleo.2019.163351]
33. [33] Balaji M., Chandrasekaran J., Raja M., Marnadu R., "Impact of Cu concentration on the properties of spray coated Cu-MoO3 thin films: evaluation of n-CuMoO3/p-Si junction diodes by JV, Norde and Cheung's methods." Materials Research Express 6, no. 10 (2019): 106404. [DOI:10.1088/2053-1591/ab361d]
Send email to the article author
| Rights and permissions | |
 |
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License. |
